Rose electronic Switch 4XE User Guide

 
Operating Instructions  
With all cabling in place and power applied to all equipment, the video monitor  
connected to KVM port #1 should display the video from computer #1 (default).  
Switching to other computers is accomplished by:  
1. Keyboard commands (press and release left Ctrl key + CPU #)  
(LCtrl + 3 switches to port #3)  
2. On-Screen-Display list of computers (Left Ctrl + Esc key)  
3. Remotely using the RS232 port and sending switching commands from a  
remotely connected computer using a communication program like  
HyperTerminal. (Sending K2C8S, enter, switches KVM #2 to CPU port #8)  
Additional keyboard commands are available for other switching methods,  
invoking the scan mode, and others. See Table 1 for a list of keyboard  
commands and their functions.  
The OSD provides a visual interface to the features, set-up and additional  
functions. The OSD is invoked by pressing and releasing the left Ctrl key, then  
the F12 key. The below menu will display for configuring the System,  
Computers, KVM. User, Profile, Group, and Language. Refer to the Installation  
and Operations manual for a detailed description of each menus features and  
options.  
To navigate through the menu system, use the arrow keys to select the  
configuration menu needed and press [Enter]. When you press [Enter] that  
menu will display, an input box will display for a new value, or a list of  
supported choices will display. Enter or select the information needed and  
press [Enter]. To return to the previous page or abort an input, press the [Esc]  
key.  
 
Keyboard commands  
The following table describes the available keyboard commands. The [Ctrl] key  
sequence is a press and release of the left control key. Commands following  
[Ctrl] must be entered within 2 seconds.  
Command  
Main Menu  
CPU List  
Key sequence  
[Ctrl] [F12]  
Description  
Displays main menu  
[Ctrl] [Esc]  
Displays CPU selection list  
Direct CPU  
connect  
[Ctrl] n [Enter]  
Connects directly to the specific  
CPU number “n”.  
Connect  
Back  
[Ctrl] [Backspace]  
[Ctrl] [Minus sign]  
[Ctrl] [Plus sign]  
Connects to the previous CPU  
Connect  
Down  
Connects to the previous CPU  
in a Group.  
Connect Up  
Connects to the next sequential  
CPU in a group  
KVM Status  
Logout  
[Ctrl] D  
[Ctrl] L  
Displays / Removes status box.  
Logs user out if the KVM station  
is configured for user logins.  
Disconnect  
[Ctrl] Q  
[Ctrl] R  
Disconnects the current CPU  
Reset  
Keyboard/  
mouse  
Resets / enables keyboard and  
mouse; enables PS/2 mouse on  
connected CPU  
Send Null  
Byte  
[Ctrl] N  
Sends a null byte to the CPU’s  
PS/2 mouse port. Use this  
command if the PS/2 mouse  
gets “out of sync”.  
Reset Mouse [Ctrl] O (not zero)  
(NT or Unix  
systems only)  
Resets the currently selected  
NT or Unix computers PS/2  
mouse. Also switches the NT  
mouse driver to “wheel” mode.  
Start Scan  
Stop Scan  
[Ctrl] S  
[Ctrl] X  
Sequentially steps through all  
connected CPUs in a group.  
Turns scan “Off”  
Table 1 - Keyboard Commands  
Copyright Rose Electronics 2007. All rights reserved.  
No part of this publication may be reproduced, stored in a retrieval system, or transcribed in any form or any  
means, electronic or mechanical, including photocopying and recording, without the prior written permission of  
Rose Electronics.  
Rose Electronics Part # QS-UME  
Printed In the United States of America  
 

RCA CRT Television 20F530T User Guide
RIDGID Soldering Gun RT 175 User Guide
Rosewill TV Mount RMS MT3710 User Guide
RoyalTek GPS Receiver REB 1315LP User Guide
Samsung Printer CLP 365W XAA User Guide
Sangean Electronics Portable Radio DT 220V User Guide
Sanyo Air Conditioner C3622 User Guide
SATO Automobile Parts Lt408 User Guide
Sears Chipper 502493 User Guide
Sears Pressure Washer 58075151 User Guide